Put two dehumidifiers of the same capacity side by side and read the electrical line. One says rated input 7,000 W. The other says 3,800 to 5,000 W. Both remove 360 litres a day. The obvious conclusion is that the second one saves 2,000 watts, and the obvious conclusion is wrong in a way that matters. Comparing inverter vs fixed-speed dehumidifiers on those two figures is the most common mistake in this category, because the figures are not describing the same thing at all.
An inverter dehumidifier is not a more efficient version of a fixed-speed one. It is a machine whose compressor speed moves with the load, and that single change alters what every figure on the sheet means.
A fixed-speed number is a snapshot. A range is a description.
A fixed-speed compressor has one speed. It is either running at that speed or it is not running. So the wattage printed on the sheet is not an average or a maximum; it is the exact electrical state of the machine for every hour the compressor happens to be on. The number is a snapshot.
What varies is the capacity. A 360 litre machine only removes 360 litres a day in the air it was rated in. Put it in a cool, dry room and it removes less per hour, so it reaches the set point and switches off. Then it waits while the room drifts back up, and restarts at full power. Nothing about the machine has changed; the load has.
An inverter compressor has a speed range instead of a speed. When the room is easy, the compressor turns slowly, and the electrical draw falls with it. Our inverter models are three-phase machines with full inverter control, and their sheets give the input as a band because there genuinely is no single figure to print. That band is not a tolerance and it is not a marketing device. It is an admission that the machine has more than one operating point, which is exactly the thing a fixed-speed sheet cannot say.

The division that makes the two sheets comparable
If one sheet quotes a constant wattage and the other quotes a range, comparing the wattages tells you nothing useful. Convert both to energy per litre of water removed. Take the rated input, multiply by 24 hours to get a daily figure, and divide by the rated capacity:
kWh per litre = rated input (W) × 24 ÷ capacity (L/day) ÷ 1,000
Do that for the models that appear in both ranges and the picture becomes a single number you can put beside a tariff:
| Model | Capacity | Rated input | kWh per litre |
| LT360-D030A, fixed speed | 360 L/day | 7,000 W | 0.467 |
| LT360-D030A, inverter | 360 L/day | 3,800–5,000 W | 0.333 at 5,000 W |
| LT480-D030A, fixed speed | 480 L/day | 13,000 W | 0.650 |
| LT480-D030A, inverter | 480 L/day | 4,500–6,000 W | 0.300 at 6,000 W |
The inverter column is quoted at the top of the input range, not the bottom, and that choice is the only honest way to fill the cell.
The sheet pairs a range of inputs with a single capacity figure. Those two statements cannot both be true across the whole band. A compressor turning at its minimum speed is not moving as much water as one turning at its maximum; if it were, the speed control would be doing nothing. So the capacity figure must belong to the top of the range, and the low end of the range describes a machine that is removing less than 360 litres a day. Quoting 0.253 kWh per litre from the bottom of the band would be arithmetically correct and practically misleading.
At the top of the band both numbers are true at the same moment, and the result is still 0.333 against 0.467 — a 29 per cent reduction for the same 360 litres. On the 480 the gap is 0.300 against 0.650, or 54 per cent. That second figure is large enough to deserve suspicion, and there is a reason for it, which the next section deals with.
Both tables also omit the condition the capacity was measured at. Every industrial dehumidifier is rated at a warm, humid reference point — 30 °C and 80 per cent relative humidity is the common convention — and a capacity figure without that condition attached cannot be compared with anything. Ask for it. The full range, including the models not in the table above, is set out on the industrial dehumidifier page, and the inverter models are on the inverter dehumidifier page.
The 0.68 kWh you cannot get below
There is a floor under all of this, and knowing where it sits tells you whether a saving is credible or invented.
Removing one kilogram of water from air means evaporating it and then condensing it. The latent heat involved is about 2,450 kilojoules per kilogram, which is 0.68 kWh of heat per litre. That is not electricity, because a dehumidifier is a heat pump and it moves heat rather than making it. The electricity it needs is the heat divided by the coefficient of performance. At a realistic COP of 2.5, one litre costs about 0.27 kWh. At 2.0 it costs 0.34.
Now place the numbers against that wall. The inverter figures of 0.300 and 0.333 sit within ten to twenty per cent of it, which is what a well-controlled variable-speed machine should do: it keeps the evaporator close to the load instead of swinging past it. The fixed-speed 360 at 0.467 is about seventy per cent above the wall. The fixed-speed 480 at 0.650 is within five per cent of the heat of vaporisation itself — in energy terms, the same electricity a resistive heating element would use to boil the water off. The mechanics of the refrigeration cycle behind that comparison are covered in how a dehumidifier works.
A figure that far out of line with its neighbours is worth a second look before you quote it. Across our fixed-speed range the draw per litre per day runs at 16 to 21 watts for most models; the 480 sits at 27. It is the weakest point in that table, and it is precisely the kind of point a variable-speed compressor removes, because the machine no longer has to be sized for a single worst-case operating state.
Where the saving actually comes from
The saving does not come from the inverter being a better compressor. It comes from the machine spending most of its life at less than full output.
Every dehumidifier is sized for a design day: the wettest hour the room will ever produce. Most hours are not that hour. A plant that needs 360 litres a day on its worst day needs perhaps 250 on a normal one, and 150 on a dry week. A fixed-speed machine answers all three cases the same way — full power, then off — because that is the only answer it has. The litres still cost what the nameplate says they cost, plus a small penalty for every restart and for the moisture that re-evaporates off the coil while the machine sits idle.
An inverter answers the easy days by turning down. The litres cost less, not because the machine is suddenly cleverer, but because it is no longer running flat out to produce a litre it could have produced gently.
Put a number on it. Take a site that removes 100,000 litres over a year — 274 litres a day on average, which is about three-quarters of a 360 litre machine’s capacity, a realistic utilisation for a unit that was sized properly:
- Fixed speed at 0.467 kWh per litre: 46,670 kWh a year.
- Inverter at 0.333 kWh per litre: 33,330 kWh a year.
- Difference: 13,340 kWh a year.
Multiply by whatever you pay. At USD 0.10 per kWh that is USD 1,334 a year; at 0.25 it is USD 3,335. We do not publish prices, so the payback calculation needs one input from you: ask for a quote on both machines and divide the price difference by the annual kWh saving at your own tariff. If the answer is more than four or five years, the inverter is not the right purchase for that site.
Also treat 13,340 kWh as a floor rather than a forecast. It assumes the inverter holds 0.333 at part load. In practice a variable-speed machine does better when it is throttled — lower condensing temperature, fewer starts, less idle re-evaporation — so the real figure should be larger. We quote the conservative one because it is the one we can defend from a published sheet.
The site where the inverter earns nothing
There is a case against buying one, and it is worth stating plainly.
If the load is flat, the inverter has nothing to do. A sealed process room with a constant exfiltration rate, a cold store in a climate that does not change, a 24/7 production hall that runs the same way in February and August — in those places the machine sits near full capacity almost every hour of the year. It never gets the chance to turn down. You have paid for a speed range you will not use, and the fixed-speed unit will deliver the same litres for less money.
The variable-speed machine pays where the load varies: seasonal humidity, batch production, doors that open. It also pays, awkwardly, where the system was oversized. A machine chosen at 140 per cent of the design load will cycle constantly if it is fixed-speed and simply run slower if it is not — not an argument for sloppy sizing, but a fair description of how many projects are bought.
The warehouse humidity control guide sets out how two warehouses with very different load profiles differ.
The humidity band you are buying along with the watts
There is a second thing on the sheet that gets less attention than the wattage and probably deserves more: the control band.
Our inverter units accept a set point anywhere from 10 to 90 per cent relative humidity, adjustable in one-point steps. The compressor and fan cut out once the room reaches the target, and do not come back on until humidity has climbed three points above it. So the machine does not hold one humidity. It holds a band three points wide, and everything sensitive in that room lives inside that band.
A fixed-speed machine traverses the band in one jump: full output until it crosses the lower edge, then nothing until the room climbs back. An inverter can reduce speed as it approaches the set point, so the same three points are crossed slowly rather than in a single overshoot. It still crosses them — nothing here eliminates a dead band — but it arrives at the lower edge with less momentum, which means less undershoot, fewer full-load starts and a room that spends more of its time near the number you set rather than at the edges of the range.
Whether that is worth paying for depends entirely on what is in the room. A warehouse storing cardboard will not notice. A room holding hygroscopic powder, film, coated tablets or seed will notice, because those materials do not respond to average humidity, they respond to the peak. The set point question itself is covered in what the ideal temperature and humidity for your room actually is; where the band has to be tighter than three points, a constant temperature and humidity unit is the correct machine and a dehumidifier is the wrong one.
The supply you did not budget for
The electrical line most buyers skip is the current, and on these machines it is the line that changes the installation cost.
The fixed-speed 360 draws 18 amps. The inverter version draws 7 to 11. The fixed-speed 480 draws 34 amps; the inverter version, 9 to 14. Apply the 125 per cent continuous-load allowance that many codes apply to fixed equipment and the fixed-speed 480 asks for a supply sized around 43 amps while the inverter asks for around 18. That is not a rounding difference. It is a different breaker, a different cable size, and on a small installation sometimes a different sub-panel.
Then there is the start. A direct-on-line compressor pulls locked-rotor current for a fraction of a second, commonly quoted at around six times running current. For the fixed-speed 480 that is a momentary 200 amps, and on a weak grid or a site running on its own generator that momentary figure is the one that trips a breaker or browns out a workshop. The inverter ramps the compressor up instead of switching it on, which is what the phrase smooth start-up on the datasheet is referring to.
For a project where the supply is the constraint rather than the tariff, this can matter more than the energy saving, and it is invisible if you only compare wattages. Where the unit physically sits changes the cable run and the service access as well, and those trade-offs are set out in ceiling-mounted versus floor-standing dehumidifiers.
Five questions, and how inverter vs fixed-speed dehumidifiers answer them
Ask in this order; it settles the decision fastest.
- What is my load on a typical day, not my design day?If the two are close, an inverter has little to work with.
- What is the reference condition behind the capacity figure?A capacity without a temperature and humidity is not a specification.
- What is the energy per litre, at the top of the input range?That is the only figure that survives the arithmetic.
- What does the site’s supply actually allow?Current, breaker, cable, and whether there is a generator behind it.
- How wide is the control band, and what in the room responds to the peak rather than the average?
Answer those five and the choice usually makes itself — sometimes in favour of the cheaper machine.
Questions we get asked
Does an inverter dehumidifier use less electricity at the same capacity?
Yes, and the size of the gap depends on the model. On our own figures a 360 litre inverter machine needs 0.333 kWh per litre against 0.467 for the fixed-speed version of the same capacity, a 29 per cent reduction, and the 480 litre pair is 0.300 against 0.650. Both comparisons use the top of the inverter’s input range, which is the least favourable reading for the inverter and the only one where the capacity figure is simultaneously true.
Why does the inverter datasheet give a wattage range instead of one number?
Because the compressor does not run at one speed. The input follows the load, so there is no single state to quote. A fixed-speed sheet can print one number precisely because the machine has no second operating point — which is a limitation, not a virtue.
Can I compare the range’s lowest figure against a fixed-speed wattage?
No. The low end of the range corresponds to a lower compressor speed and therefore lower water removal; pairing it with the full capacity figure produces an artificially good number. It is the most common way this comparison gets misused.
Will an inverter dehumidifier work in a cold room?
It will run, and it will use more energy per litre than the warm-air figures suggest. Below about 18 °C the evaporator frosts, and the machine stops dehumidifying periodically to defrost the coil. That time is not removing water, so the same litre costs more. If the room is consistently cold, the machine needs to be chosen for that duty rather than for its warm-air rating — see the cold room dehumidifier guide for how the selection changes.
Is a variable-speed dehumidifier the same thing as an inverter dehumidifier?
In practice the two terms describe the same mechanism: a compressor whose speed is varied by an inverter drive. The phrase worth checking on a datasheet is whether the compressor itself is inverter-driven or whether only the fan is. Our units are described as full inverter type, which refers to the compressor.
Where does an inverter dehumidifier not make sense?
Where the load is flat. A sealed process room, a cold store in a stable climate, or a plant that runs identically all year will keep the machine near full output, and the speed range will never be used. The same applies where the electricity is cheap and the capital budget is not.
Talk to us about your load profile and we will tell you which of the two we would put in, including when the answer is the cheaper one.